RELANCE 0-60063-1 監控驅動
小修項目
DCS系統小修隨機組小修進行，小修項目應包括以下內容：
1) 清理盤柜防塵濾網，檢查各種冷卻風扇。
2) 電源及模件工作狀態檢查。
3) 硬件設備功能試驗。
4) 消除運行中無法處理的缺陷。
5) 部分就地設備檢修;部分I/O模件校驗。
6) 機組主保護及聯鎖試驗
根據計算機控制設備特點，DCS除像常規控制設備一樣進行外圍設備檢修外，隨機組大小修至少要進行以下項目的檢修，即模件組態拷貝，核實控制模件標志和地址;清掃電源、模件及防塵濾網，檢查緊固控制柜接線，進行接地系統檢查，冷卻風扇檢修，電源設備檢修測試;重要測量和保護信號線路絕緣檢查;電子室溫度、濕度及含塵量檢修前測試，檢修后復查;模件電源及冗余模件的切換試驗;報警及保護功能測試;通信、手動操作站檢查;進行卡進行校驗等;檢修前要做好充分的準備工作，檢修中要嚴格執行工序卡制度，并認真做好檢修記錄，對電源、模件等測試要仔細填寫測試報告。
Pay attention to the situation where all operating stations are powered off
At this time, check if the power indicator light of the control station is normal, and if there is a fault in the card diagnosis indicator light. The red light and green light indicate that the card is working normally. If all of the above are normal, it can be determined that the control station is working normally and the self adjustment system is working normally. However, the operator cannot see the monitoring screen temporarily and cannot perform remote control operations on site. Immediately notify the microcomputer maintenance personnel to repair and go to the site for monitoring.
Pay attention to the situation where all control stations are powered off
Due to the dual power supply of all control station equipment, one UPS and one mains power supply, the probability of this situation occurring is very low.
When the control station is completely powered off, the two system alarm red lights on the monitoring screen light up, communication is interrupted, and all data is not refreshed. All self regulating systems are completely out of control, and the regulating valve will return to its initial state. The air opening valve will be fully closed, and the air closing valve will be fully open. At this time, emergency handling or parking should be carried out immediately, and the operation should be carried out on-site at the same time.
Observe the power outage situation of the operation station
If some operation stations suddenly do not display, it indicates that the UPS or mains power is cut off, and the microcomputer maintenance worker is immediately notified for repair. If the operating station with electricity can monitor normally, it will not affect the normal adjustment of the control system.