RELANCE 0-60029-1 電源控制器
根據計算機控制設備特點，DCS除像常規控制設備一樣進行外圍設備檢修外，隨機組大小修至少要進行以下項目的檢修，即模件組態拷貝，核實控制模件標志和地址;清掃電源、模件及防塵濾網，檢查緊固控制柜接線，進行接地系統檢查，冷卻風扇檢修，電源設備檢修測試;重要測量和保護信號線路絕緣檢查;電子室溫度、濕度及含塵量檢修前測試，檢修后復查;模件電源及冗余模件的切換試驗;報警及保護功能測試;通信、手動操作站檢查;進行卡進行校驗等;檢修前要做好充分的準備工作，檢修中要嚴格執行工序卡制度，并認真做好檢修記錄，對電源、模件等測試要仔細填寫測試報告。
大修項目
DCS系統大修隨機組主設備大修進行，大修項目因包括以下內容：
1) 對控制設備進行全面檢查，作好記錄。
2) 拷貝所有模件的組態，核實模件的標志和地址。
3) 清掃控制柜電源及模件，清理盤柜防塵濾網。
4) 檢查、緊固控制柜接線及固定螺絲。
5) 接地系統檢查，電源性能測試，線路絕緣測試。
6) 對控制柜進行防塵、密封處理，更換冷卻風扇。
7) 記錄儀、打印機、報警窗、人機接口設備等檢修。
8) 消除運行中無法處理的缺陷，恢復和完善各種標志。
9) 硬件設備功能試驗，組態軟件裝載及檢查。
10)測量模件校驗，現場設備檢修。
11)保護聯鎖試驗。
12)電纜、管路及其附件檢查、更換。
View the working status of the operation station
When a certain operating station crashes, the monitoring screen data does not refresh, and the adjustment screen does not work, check whether the upper right system alarm indicator light is normal, and check whether other operating stations are working properly. If it is normal, only that operating station has a problem, and notify the microcomputer maintenance personnel to repair it. If the data from other operating stations remains unchanged, it indicates a malfunction in the system communication network. Immediately notify maintenance personnel to check the operation of the network equipment and repair it.
the fluctuation data has no direct impact on each other in terms of technology, it may be due to a malfunction of a certain card in the microcomputer. Immediately switch the relevant self adjustment system to manual adjustment, and if necessary, go to the site for adjustment. At the same time, notify the microcomputer and instrument personnel to check.
Determine whether the fluctuation data is a process related parameter. If it is a related parameter, notify the instrument and microcomputer personnel to check whether a certain adjustment system fluctuation causes a change in the related parameters. At the same time, put the relevant adjustment system in manual mode and adjust it on-site if necessary. In a water solution full circulation device, when the pressure of the urea synthesis tower is normal, it is 19.67 MPa. If there is a sudden large-scale fluctuation, it will inevitably cause pressure fluctuations in the downstream medium pressure and low pressure systems. This situation is due to fluctuations in one of several related parameters causing changes in other parameters, not the control system itself.