PROSOFT MVI56-LTQ 控制系統
9級別1僅記錄錯誤。這是大多數應用程序的建議設置。MVI56-LTQ級別2到4會越來越詳細地記錄信息性事件。使用這些級別進行故障排除和支持。MVI56-LTQ級別0僅記錄內部系統錯誤。必須重新啟動掃描儀，新的日志級別才能生效。單擊MVI56-LTQ按鈕以重新啟動掃描儀。系統將提示您確認重新初始化。清除事件日志從模塊中清除整個事件日志。這是無法撤消的。更新您可以從此頁面更新模塊的固件。只有在MVI56-LTQ技術支持指示您更新固件的情況下，您才應該更新固件。單擊瀏覽按鈕以選擇計算機上的固件文件。固件文件的文件擴展名為“fwa”。單擊UPDATE按鈕對模塊執行更新。系統將提示您確認更新。重要提示：在更新完成之前，請勿循環供電或斷開以太網電纜。重要提示：重新啟動模塊后，您必須清除瀏覽器的緩存（工具/刪除瀏覽歷史記錄/臨時MVI56-LTQ文件），以確保舊頁面已從瀏覽器的內存中清除。重新啟動單擊MVI56-LTQ按鈕以重新啟動模塊。系統將提示您確認重新啟動。
您可以為每個端口配置以下設置。· 殘廢· 靜態IP地址o子網掩碼o默認網關（可選）· DHCP（通過DHCP服務器自動配置）單擊“保存”按鈕更新模塊上的這些設置。您可以在模塊上執行的系統功能包括：功能描述備份通過檢查CONFIGURATION（配置）和/或ADMINISTRATIVE settings（管理設置）從模塊中選擇要備份的設置。然后單擊MVI56-LTQ按鈕將當前模塊配置備份到計算機上的文件中。ADMINISTRATIVE SETTINGS備份所有模塊配置設置，包括網絡設置、設備名稱等。MVI56-LTQ僅備份與數據傳輸相關的信息。然后，您可以使用此備份文件配置具有相同設置的另一個模塊?；謴蛦螕魹g覽按鈕從計算機中選擇以前保存的配置文件。MVI56-LTQ 單擊RESTORE按鈕將模塊恢復到配置文件中保存的狀態。配置恢復后，模塊將重新啟動。系統將提示您確認配置還原并重新啟動。設置日志級別設置掃描儀模塊將記錄事件的日志級別。
Update You can update the module's firmware from this page. You should only update the firmware if you have been directed to do so by ProSoft Technical Support. Click the BROWSE button to select the firmware file on your computer. Firmware files have the file extension "fwa". Click the UPDATE button to perform the update on the module. You will be prompted to confirm the update. Important: Do not cycle power or disconnect the Ethernet cable until the update is complete. Important:MVI56-LTQ You must clear your browser's cache (Tools/Delete Browsing History/Temporary Internet Files) after rebooting the module to ensure the old pages have been cleared from your browser's memory.MVI56-LTQ Reboot Click the REBOOT button to reboot the module. You will be prompted to confirm the reboot.
MVI56-LTQ Restore Click the BROWSE button to select a previously saved configuration file from your computer. Click the RESTORE button to restore the module to the state saved in the configuration file. The module is rebooted after the configuration is restored. You will be prompted to confirm the configuration restore and reboot. Set Log Level Set the log level at which the scanner module will record events. § Level 1 logs errors only. This is the recommended setting for most applications. § Levels 2 through 4 log informational events in increasing detail. Use these levels for troubleshooting and support. § Level 0 logs only internal system errors. The scanner must be restarted before the new log level will take effect.MVI56-LTQ Click the REINITIALIZE button to restart the scanner. You will be prompted to confirm the reinitialize. Clear Event Logs Clears the entire Event Log from the module. This cannot be undone.
You can configure the following settings for each port. · Disabled · Static IP Address o Subnet Mask o Default Gateway (optional) ·MVI56-LTQ DHCP (auto-configured through a DHCP server) Click the SAVE button to update these settings on the module.System functions you can execute on the module include: Function Description Backup Choose which settings from the module you would like to backup by checking CONFIGURATION and/or ADMINISTRATIVE SETTINGS. Then click the BACKUP button to backup the current module configuration(s) to a file on your computer. ADMINISTRATIVE SETTINGS backs up all module configuration settings,MVI56-LTQ including network settings, device name, and so on. CONFIGURATION backs up the only the information that pertains to the transfer of data.MVI56-LTQ You can then use this backup file to configure another module with the same settings.