PROSOFT MVI56-GEC 通用串行
維修工具軟件位于MVI56-GEC（個人電腦）上，并通過驅動程序的9針維修端口與ProAct驅動程序通信。各種用戶可使用以下模式：出廠校準、測試、配置、用戶校準、調整和監控模式（見下圖的操作模式）。工廠校準和測試模式是Woodward內部獨有的選項；客戶可以使用其他所有功能。維修工具模式受密碼保護，以防止無意中更改程序。MVI56-GEC功能始終可用，不受密碼保護。為了安全起見，只有在機組關閉時才能進入密碼保護模式。可以通過維修工具命令或打開低功率待機模式離散輸入來關閉機組。
連接到模塊的網頁如果您的網絡配置為使用MVI56-GEC范圍內的IP地址，請打開MVI56-GEC（版本7或更高版本），然后連接到以下地址：MVI56-GEC如果您的網絡配置為使用不同的IP范圍，請執行以下步驟：1斷開電腦與網絡的連接2連接電腦上的以太網端口和模塊上的端口1之間的以太網電纜3臨時更改電腦上的IP地址和子網掩碼以匹配模塊上的網絡配置：IP地址：MVI56-GEC子網掩碼：MVI56-GEC重要提示：記下您的IP地址設置。在重新連接到網絡之前，您需要恢復這些設置。
Connect to the module's web page again at the module's new IP address. The following table describes the default Ethernet port configuration and login information. Factory Default settings Ethernet Ports: Port 1 Port 2 IP: 192.168.1.254. DHCP User Name: admin Password: admin Important: The User Name and Password are case-sensitive. 1.8 Logging In You can view the status and configuration of the MVI56-GEC without logging in. However, to modify the module's configuration, or to perform maintenance tasks, you must log in. The LOGIN and LOGOUT buttons are located in the status bar at the bottom of the module's web page. To Log In Click the LOGIN button on the status bar at the bottom of the page.The module has two RJ45 Ethernet ports, located at the bottom of the front panel on the module.
Open Microsoft Internet Explorer (version 7, or higher) and connect to the following address:MVI56-GEC Click the LOGIN button at the bottom of the screen, and use the following username and password to login. Username: admin Password: admin 6 Click the MVI56-GECtab, and then the MVI56-GECtab. Configure the IP Address, Subnet Mask, and Default Gateway to work with your network. 7 Click the SAVE button to apply the updated settings 8 Change the IP Address and Subnet Mask settings on your PC back to their original values, and then reconnect your PC to the network.
Connect to the Module's Web Page If your network is configured to use IP addresses in the rangeMVI56-GEC, open Microsoft Internet Explorer (version 7, or higher), and connect to the following address: MVI56-GECIf your network is configured to use a different IP range, follow these steps: 1 Disconnect your PC from the network 2 Connect the Ethernet cable between the Ethernet port on your PC and Port 1 on the module 3 Temporarily change the IP address and Subnet Mask on your PC to match the network configuration on the module: IP address: MVI56-GEC Subnet mask: MVI56-GEC Important: Make a note of your IP Address settings. You will need to restore these settings before you reconnect to the network.