PROSOFT ILX34-MBS485 網關轉換器
更深的槽用于擴大針閥的頭部并增加摩擦力，以防止因改變針閥設置而引起的振動。如果必須使用普通螺絲刀，一定要使用針閥的淺槽。讓原動機擺動約30秒，以排出調速器油道中的滯留空氣。2.松開固定補償指針的螺母，剛好使指針盡可能降低，以獲得最小補償。再次擰緊螺母。補償調整程序的目的是找到補償針閥和補償調整指針的特定設置，在該設置下，發動機、渦輪機或其他類型的原動機在速度擾動后僅輕微過沖或下沖（補償指針調整）即可快速恢復速度（針閥調整）。3.逐漸關閉針閥，直到振蕩停止。如果振蕩沒有停止，打開針閥一圈，并將補償指針向上移動前面板指示器刻度上的一個標記。再次逐漸關閉針閥，直到振蕩停止。如果振蕩沒有停止，將針閥打開1/4圈，并重復將補償指針向上設置一個標記。重新測試調速器，直到振蕩停止。
逐漸關閉針閥，直到振蕩停止。如果振蕩沒有停止，打開針閥一圈，并將補償指針向上移動前面板指示器刻度上的一個標記。再次逐漸關閉針閥，直到振蕩停止。如果振蕩沒有停止，將針閥打開1/4圈，并重復將補償指針向上設置一個標記。重新測試調速器，直到振蕩停止。當發動機或渦輪機在調速器充油后首次啟動時，調速器可能在恒定速度下穩定，但調速器可能需要調整。負載變化后的高速和低速以及緩慢恢復到正常速度表明需要進行補償調整。最大補償設置通常提供穩定的穩態操作，但在負載變化時會導致更大的斷開速度。調速器中的油達到其正常工作溫度后，在原動機無負載的情況下進行以下補償調整，以確保調速器提供最佳控制。調整部件的位置見圖1-1。1.要排出調速器油道中的滯留空氣，首先擰松固定補償調節指針的螺母，使指針處于其向上的極限位置，以獲得最大補償。接下來，拆下針閥檢修塞并逆時針打開針閥兩圈。使用十字螺絲刀避免損壞孔內的螺紋和針閥。螺紋或針閥損壞會導致調速器有節奏地更換燃油。這就是所謂的州長狩獵。有關狩獵的更多信息，請參閱第5章。針閥中有兩個螺絲刀槽，一個淺槽和一個深槽，彼此成直角。
If the linkage to engine is correctly adjusted, the engine will shut down.efer to Figure 3-1 with the text to better understand the operation of the UG Lever governor. This schematic diagram is of a basic design and does not include any auxiliary equipment. This description is based on speed changes resulting from load changes. However, the same sequence of governor movements would occur if the governor speed setting were changed by repositioning the speed control linkage. Decrease in Load Assume the prime mover is running on-speed. The flyweights are in a vertical position for normal steady-state operation. The control land of the pilot valve plunger (14) is centered over the control port of the rotating bushing (5304-MBP-PDPM). This stops the flow of pressure oil through the bushing (15) control port. As a result, there is no movement of the power piston (7) and no movement of the governor output shaft (6).
Loosen the nut holding the compensation pointer just enough to lower the pointer as far as it will go for minimum compensation. Tighten the nut again. The objective of the compensation adjustment procedure is to find the particular settings for the compensation needle valve and compensation adjustment pointer at which the engine, turbine, or other type of prime mover will return quickly to speed (needle valve adjustment) after a speed disturbance with only a slight over or undershoot (compensation pointer adjustment). 3. Gradually close the needle valve until hunting just stops. If hunting does not stop, open the needle valve one turn and move the compensation pointer up by one mark on the front panel indicator scale. Again gradually close the needle valve until hunting stops. If hunting does not stop, set the needle valve 1/4 turn open and repeat setting the compensation pointer up by one mark. Retest the governor until hunting stops.
Gradually close the needle valve until hunting just stops. If hunting does not stop, open the needle valve one turn and move the compensation pointer up by one mark on the front panel indicator scale. Again gradually close the needle valve until hunting stops. If hunting does not stop, set the needle valve 1/4 turn open and repeat setting the compensation pointer up by one mark. Retest the governor until hunting stops.When the engine or turbine is started for the first time after the governor has been filled with oil, the governor may be stable at constant speed, yet the governor may need adjustment. High overspeeds and underspeeds after load changes and slow return to normal speed indicate the need for compensation adjustment. Maximum compensation settings generally provide stable steady state operation but result in greater off-speeds on load changes. After the oil in the governor has reached its normal operating temperature, make the following compensation adjustments without load on the prime mover to be certain that the governor gives optimum control. See Figure 1-1 for location of the adjustment parts.