LAM 853-190023-001 平面分開
為了幫助系統集成商，PXI Express機箱和系統模塊的制造商必須記錄其產品的功能。.ini文件包含最低文檔要求，這些文件由ASCII文本組成。系統集成商、配置實用程序和設備驅動程序可以使用這些.ini文件。NI PXIe-1085系列機箱的功能說明文件包含在機箱附帶的軟件介質上的chassis.ini文件中。此文件中的信息與系統控制器的信息相結合，可創建一個名為pxisys.ini（PXI系統初始化）的系統初始化文件。系統控制器制造商為包含系統控制器的特定機箱型號提供一個pxisys.ini文件，或者提供一個實用程序，可以讀取任意的chassis.ini文件并生成相應的pxisys ini文件。NI的系統控制器為NI PXIe-1085系列機箱提供了pxisys.ini文件，因此不需要使用chassis.ini文件。
一些National Instruments機箱，如NI PXIe-1085系列和NI PXI-1044/1045，能夠使用MAX中的觸發器路由選項卡將觸發器從同一機箱內的一條總線路由到另一條總線，如圖2-10所示。注意：選擇任何未禁用的路由都會自動保留要路由到的所有觸發總線中的線路。如果您使用NI DAQmx，它會為您保留和路由觸發線路，因此您不必手動路由觸發線路。完成以下步驟以在MAX.1中配置觸發器路由。在配置樹中，選擇要在其中路由觸發線路的機箱。2.在右側窗格中，選擇底部附近的觸發器路由選項卡。3.對于每條觸發線，選擇“向右布線”、“從中間向外布線”或“向左布線”以在所述方向上布線該線上的觸發器，或者選擇“禁用”作為不使用手動布線的默認行為。4.單擊“應用”按鈕。使用系統配置和初始化文件PXI Express規范允許PXI Express機箱和系統模塊的多種組合。
Some National Instruments chassis, such as the NI PXIe-1085 Series and the NI PXI-1044/1045, have the capability to route triggers from one bus to others within the same chassis using the Trigger Routing tab in MAX, as shown in Figure 2-10. Note Selecting any non-disabled routing automatically reserves the line in all trigger buses being routed to. If you are using NI-DAQmx, it will reserve and route trigger lines for you, so you won’t have to route trigger lines manually. Complete the following steps to configure trigger routings in MAX. 1. In the Configuration tree, select the chassis in which you want to route trigger lines. 2. In the right-hand pane, select the Trigger Routing tab near the bottom.
PXI-1 System Configuration 1. Launch MAX. 2. In the Configuration tree, click the Devices and Interfaces branch to expand it. 3. If the PXI system controller has not yet been configured, it is labeled PXI System (Unidentified). Right-click this entry to display the pop-up menu, then select the appropriate system controller model from the Identify As submenu. 4. Click the PXI system controller. The chassis (or multiple chassis, in a multichassis configuration) is listed below it. Identify each chassis by right-clicking its entry, then selecting the appropriate chassis model through the Identify As submenu. Further expanding the PXI System branch shows all devices in the system that can be recognized by NI-VISA. When your system controller and all your chassis are identified, the required pxisys.ini file is complete.
PXI-1 System Configuration 1. Launch MAX. 2. In the Configuration tree, click the Devices and Interfaces branch to expand it. 3. If the PXI system controller has not yet been configured, it is labeled PXI System (Unidentified). Right-click this entry to display the pop-up menu, then select the appropriate system controller model from the Identify As submenu. 4. Click the PXI system controller. The chassis (or multiple chassis, in a multichassis configuration) is listed below it. Identify each chassis by right-clicking its entry, then selecting the appropriate chassis model through the Identify As submenu. Further expanding the PXI System branch shows all devices in the system that can be recognized by NI-VISA. When your system controller and all your chassis are identified, the required pxisys.ini file is complete.