LAM 810-802901-305 開關量
如果裝置的配置出現錯誤，810-802901-305（配置錯誤）關閉將使驅動器處于關閉狀態。配置錯誤的確切原因在配置模式選項卡頁上確定（請參閱配置錯誤部分）。配置錯誤配置完成后，將執行有效性檢查。如果檢測到錯誤，將發出Config error（配置錯誤）停機，并且在清除之前，機組不會運行。配置錯誤的原因可以從配置模式選項卡頁上的錯誤代碼和錯誤信息值中確定。錯誤代碼錯誤信息（顯示文本）0配置中沒有錯誤810-802901-305主/備用信號選擇相同（主需求和備用需求配置為同一源）102主需求信號選擇無效（主需求選擇配置為超出范圍的值）810-802901-305備用需求信號選擇無效（備用需求選擇配置為超出范圍值）104執行機構慣性設置值過大（執行機構慣性設定選擇配置為超過范圍值）810-802901-305無效執行機構類型選擇（執行機構類型配置為超出范圍值）
進入配置模式選擇配置模式選項卡頁，通過將關閉命令值設置為“true”或打開低功率待機模式離散輸入來關閉驅動程序。輸入適當?shù)呐渲媚Ｊ矫艽a（1113），810-802901-305然后選擇“輸入”或單擊密碼框右側的等于（=）框。如果已成功進入配置模式，“啟用”字段將顯示“true”。通過將裝置設置和需求設置參數設置為特定于應用程序的值來配置裝置。有關這些設置的詳細信息，請參閱手冊的配置模式詳細信息部分。當對配置和服務模式參數進行更改時，它們會自動保存到非易失性存儲器中——不需要特殊的“保存”命令。配置機組（配置模式參數）有關配置模式參數的詳細信息，請參閱本章后面提供的信息。附錄中提供了程序摘要工作表，作為ProAct控件中所有軟件設置的概述。退出配置模式選擇配置模式選項卡頁，并將EXIT值設置為“true”。通過將停機命令值設置回“false”810-802901-305或關閉低功率待機模式離散輸入，使機組返回運行（操作）狀態。如果成功，維修模式/機組狀態將顯示“正在運行”（810-802901-305）。
810-802901-305If an error is detected, the Config Error shutdown is issued and the unit will not run until it is cleared. The cause of the Configuration Error can be determined from the Error Code and Error Info values on the Configure Mode tab sheet.810-802901-305 Error Code Error Info (displayed text) 0 No errors in configuration 101 Primary / Backup signal selection same (the primary demand and backup demands are configured for the same source) 102 Invalid primary demand signal selection (the primary demand selection is configured for an out of range value) 103 Invalid backup demand signal selection (the backup demand selection is configured for an out of range value) 104 Actuator Inertia setting value too large (the actuator inertia setting selection is configured for an out of range value) 105 Invalid Actuator type selection 810-802901-305(the actuator type is configured for an out of range value)
Configuring the Unit810-802901-305 (Configure Mode parameters) Refer to the information provided later in this chapter for details on the Configure Mode parameters. A program summary worksheet is provided in the Appendix as an overview of all software settings in the ProAct control. Exiting Configure Mode Select the Configure Mode tab sheet and set the EXIT value to ‘true’. Return the unit to a running (operational) state by setting the Shutdown Command value back to ‘false’ or by closing the Low Power Standby Mode discrete input. The Service Mode / Unit Status will display ‘running’ if successful (refer to the Service Mode Details section). If an error was made in the unit’s configuration, a 810-802901-305 Config Error shutdown will hold the driver in a shutdown state. The exact cause of the Configuration Error is identified on the Configure Mode tab sheet (see Configuration Error section). Configuration Error Upon completion of the configuration 810-802901-305, a validity check is performed.
Entering Configure Mode Select the Configure Mode tab sheet and shut down the driver by setting the Shutdown Command value to ‘true’ or 810-802901-305 by opening the Low Power Standby Mode discrete input. Enter the appropriate configure mode Password (1113) and either select ‘ENTER’ or click on the equals (=) box to the right of the password box. The ‘Enabled’ field will display 810-802901-305‘true’ if the Configure Mode has been successfully entered. Configure the unit by setting the Unit Setup and Demand Setup parameters to the application specific values. Refer to the Configure Mode Details section of the manual for details on these settings. As changes are made to Configure and Service mode parameters, they are automatically saved into non-volatile memory—no special ‘save’ command is required.810-802901-305