LAM 810-800256-004 中央集線器
810-800256-004配置中的錯誤將不允許執行機構運行，并將導致配置錯誤停機。錯誤代碼解釋（與下面的錯誤信息相同）0配置中沒有錯誤101主/備用信號選擇相同102無效的主需求信號選擇103無效的備用需求信號選擇104執行器慣性設置值太大105無效的執行器類型選擇106無效的PwmIn最大/最小占空比值107無效的Analog in最大/分鐘值108 CAN擴展必須非零錯誤信息（僅狀態指示）配置狀態的字符串指示（另請參閱錯誤代碼）。810-800256-004配置中的錯誤將不允許執行機構運行，并將導致配置錯誤停機（請參閱停機信息）。810-800256-004關閉命令dflt=false（false，true）RS-232命令，關閉執行器驅動器。請參閱停機。配置：機組設置機組設置類別設置關鍵的執行機構和控制器信息。810-800256-004。在維修模式下可獲得其他執行機構參數（請參閱“硬件調整”）。
Password dflt=0配置模式的密碼輸入命令810-800256-004。要輸入值，請突出顯示或刪除默認值（“0”），然后使用鍵盤輸入數字密碼。當按下回車鍵或選擇輸入右側的等號時，接受輸入。輸入后，密碼將返回零。如果接受并關閉裝置，“啟用”指示將為真。有關維修工具密碼，請參閱附錄。已啟用（僅狀態指示）配置模式已啟用指示（真/假）。810-800256-004啟用模式時，參數為true–這表示可以更改配置模式參數。810-800256-004如果為false，則只能查看參數，而不能進行調整。退出dflt=false（僅限瞬時真命令）退出命令。設置為true可退出配置模式。這將禁用在此模式下更改參數的功能。810-800256-004“退出”參數在退出完成后自動返回false。錯誤代碼（僅狀態指示）配置狀態的整數指示（另請參閱錯誤信息）。
(status indication only) String Indication of the status of the configuration (see also Error Code).810-800256-004 An error in the configuration will not allow the actuator to operate and will result in a Configuration Error Shutdown (see information on shutdowns).810-800256-004 Shutdown Command dflt = false (false, true) RS-232 Command to shut the actuator driver down. Refer to shutdowns. Configure: Unit Setup The Unit Setup category sets critical actuator and controller information. Refer to Figure 9-2.810-800256-004 Additional actuator parameters are available in the Service Mode (see ‘Hardware Adjustments’).
This disables the ability to make changes to parameters in this mode. The ‘Exit’ parameter automatically returns to false when the exit is completed. Error Code (status indication only) Integer Indication of the status of the configuration (see also Error Info).810-800256-004 An error in the configuration will not allow the actuator to operate and will result in a Configuration Error Shutdown. Error Code Interpretation (same as Error Info below) 0 No errors in configuration 101 Primary / Backup signal selection same 102 Invalid primary demand signal selection 103 Invalid backup demand signal selection 104 Actuator Inertia setting value too large 105 Invalid Actuator type selection 106 Invalid PwmIn max/min duty values 107 Invalid AnalogIn max/min values 108 CAN Extensions must be non-zero Error Info
810-800256-004 Password dflt =0 Password input command for the Configure mode. To enter a value, highlight or delete the default value (‘0’) and use the keypad to enter the numeric password. The input is accepted when the enter key is pressed or the equals sign to the right of the input is selected.810-800256-004 When entered, the password returns to zero. If accepted and the unit is shut down, the 810-800256-004‘Enabled’ indication will be true. Refer to the Appendix for Service Tool passwords. Enabled (status indication only) Configure Mode Enabled Indication (true/false). Parameter is true when the mode is enabled – this indicates Configure mode parameters can be changed. When false, parameters can only be viewed – not adjusted. Exit dflt = false (momentary true command only) Exit command. Set to true to exit the Configure mode.810-800256-004