LAM 810-072687-111 接口板
產品概述：
810-072687-111如果執行器發出嗡嗡聲，或具有快速限位循環：?810-072687-111 設置“高摩擦負載”=False，可在“服務模式：調整用戶停止”選項卡頁中找到。? 降低執行器慣性設置并重新運行慣性測試（維修模式：調整用戶停止選項卡）。? 檢查連桿是否松動。如果致動器在臺階上過沖，或阻尼不良：? 810-072687-111增加執行器慣性設置并重新運行慣性測試（維修模式：調整用戶停止選項卡）。如果執行機構具有慢速限位循環：? 810-072687-111將“高摩擦負載”設置為True，可在“服務模式：調整用戶停止”選項卡頁中找到。? 增加執行器慣性設置并重新運行慣性測試（維修模式：調整用戶停止選項卡）。? 釋放卡住的懸掛機構或負載。
810-072687-111CAN通信如果CAN端口工作不正常，請驗證以下內容：? 檢查接線，在接線板上尋找松動的連接以及斷開或錯誤連接的電纜。如果需要，檢查終端電阻器的接線。? 檢查ProAct維修工具和速度控制中配置的數據速率（250、500、1000 kbps）。? 驗證是否配置了適當?shù)臄U展集。? 驗證是否使用了適當?shù)脑O(shè)備地址。檢查CAN ID離散輸入——它們僅在通電期間受到監控，因此ProAct電源可能需要循環。810-072687-111此參數也可以使用維修工具進行驗證，并監控單元狀態選項卡頁下的維修模式can ProAct編號。? 如果接線錯誤，CAN驅動程序芯片可能會出現故障。當CAN Hi或Lo連接無意中連接到30V或更高時，可能會發生這種情況。此故障需要在工廠更換CAN驅動程序芯片。性能故障排除指南一般性能問題? 驗證是否設置了適當?shù)膽T性數。嘗試增加并測試“慣性設置”以提高性能——請參閱“服務模式：調整用戶停止”選項卡頁。? 如果Watch Window Professional可用，運行具有內部生成的需求的執行器（測試模式2），810-072687-111以檢查需求信號問題。
If Watch Window Professional is available, run the actuator with an internally generated demand (test mode 2) to check for demand signal problems.810-072687-111 If the actuator buzzes, or has a fast limit cycle: · Set “High Friction Load” = False, found on the Service Mode: 810-072687-111Adjust User Stops tab sheet. · Decrease the Actuator Inertia Setting and re-run the Inertia Test (Service Mode: Adjust User Stops tab sheet). · Check for loose linkage. If the actuator overshoots on steps, or is poorly damped: · Increase the Actuator Inertia Setting and re-run the Inertia Test (Service Mode: Adjust User Stops tab sheet). If the actuator has a slow limit cycle810-072687-111
Verify the appropriate Extension Set is configured. · Verify the appropriate Device address is utilized. Check the CAN ID discrete inputs—they are only monitored during a power up, so ProAct power may need to be cycled. This parameter can also be verified using the Service Tool and monitor the Service Mode CAN ProAct Number under the Unit Status tab sheet. ·810-072687-111 If mis-wired, the CAN driver chip can fail. This could occur when the CAN Hi or Lo connections are inadvertently wired to 30V or more. This failure requires a factory replacement of the CAN driver chip. Performance Troubleshooting Guide General Performance Problems · Verify appropriate Inertia Number is set. 810-072687-111Try increasing and testing Inertia Setting to improve performance—refer to the Service Mode: Adjust User Stops tab sheet.
CAN Communications 810-072687-111If a CAN port is not functioning properly, verify the following: · Check the wiring, look for a loose connection at the terminal blocks and disconnected or misconnected cables. Check wiring of termination resistor, if required. · 810-072687-111Check the configured data rate (250, 500, 1000 kbps) in both the ProAct Service Tool and the speed control.810-072687-111