LAM 810-017075-003 電源板
產品概述：
810-017075-003命令清除所有錯誤的錯誤日志。發出時，所有代碼、計數器和時間都設置為零。選擇清除錯誤日志后，重置時間將更改為當前運行時小時數（顯示在“機組狀態”下）。重置時存在的錯誤不會重新記錄，只記錄新觸發的事件。上次報警事件代碼指示上次報警條件。上次停機事件代碼指示上次停機條件。ErrorLog重置時間相對于上一個“Clear ErrorLog”命令的運行時間（參見機組狀態選項卡頁）的時間。810-017075-003Entryxx ErrorCode整數指示檢測到的報警或停機事件。整數對應于報警或停機文本中列出的括號中的數字，810-017075-003例如“PWM無信號（53）”為代碼53。Entryxx計數器810-017075-003自上次清除日志以來檢測到該項的次數。
Entryxx時間第一次檢測到的事件的時間，810-017075-003以小時為單位，與上次清除日志后裝置運行的時間相關。記錄的時間基于運行時小時數（在“機組狀態”選項卡頁下找到）和錯誤日志重置時間之間的差異。例如，如果發生故障，并且這是該故障的第一次發生，則記錄的時間將為431-假定運行時小時數=641810-017075-003，錯誤日志重置時間=210。另一個示例，如果Entryxx時間為55，重置時間為200，則發生時間為運行時255小時
Demand–Can Demand (%)—Continuously updated indication, even when failed, of the CAN position demand signal in percentage of the user calibrated range.810-017075-003 Demand–PWM Demand (%)—Continuously updated indication, even when failed, of the PWM input position demand signal in percentage of the user calibrated range. Xfer to Backup—When set to true, this user command forces the demand signal from primary to the configured backup signal. The force is not performed if the backup demand is failed or if the ‘Xfer to Primary’ command is true. Used to test primary/backup transfers and to facilitate the code required with the addition of daughter board commands. Xfer to Primary—User command to transfer control from backup to the configured primary signal (if it’s not failed). Normally this would happen automatically if the primary is properly tracking.810-017075-003 This command forces transfer to primary even though it may not be tracking the backup within tolerances set in the Service mode.
This command overrides the ‘Xfer to Backup’ command by transferring the demand to primary control and setting ‘Xfer to Backup’ to false.810-017075-003 Service: Status Errors—Alarms The Status Errors—Alarms tab sheet contains status information on all monitored actuator alarms.810-017075-003 Values that are TRUE,810-017075-003 indicate the alarm condition is active810-017075-003. The Alarm indication is non-latching and returns to false when the condition no longer exists. Refer to the Alarm diagnostics in Chapter 6 for details.810-017075-003
Clear ErrorLog—Command to clear the error log of all errors. When issued, all Codes, Counters, and Times are set to zero. When a Clear Error Log is selected,810-017075-003 the reset time changes to the present runtime hours (displayed under Unit Status). Errors that exist at the time of the reset are not re-logged, only newly triggered events. Last Alarm—Event code indication of the last alarm condition. Last Shutdown—Event code indication of the last shutdown condition. ErrorLog Reset Time—Time, relative to the Run Time (See Unit Status tab sheet), of the last ‘Clear ErrorLog’ command. Entryxx ErrorCode—Integer indication of the detected alarm or shutdown event.