LAM 605-707109-012 Plc網絡接口模塊
產品概述：
校準完成后，將605-707109-012 Plc模式退出）設置為true，以返回到上一個（停機）模式。服務：調整用戶停止（必須關閉并輸入密碼）此類別提供在調整用戶停止模式中更改參數的權限。605-707109-012 Plc。它提供了自動和手動設置停止、慣性設置和測試能力以及退出命令的方式，給出模式狀態，并識別配置中的錯誤。
模式密碼dflt=0調整用戶停止模式的密碼輸入命令。605-707109-012 Plc要輸入值，請突出顯示或刪除默認值（“0”），然后使用鍵盤輸入數字密碼。當按下回車鍵或選擇輸入右側的等號時，接受輸入。輸入后，密碼將返回零。如果接受并關閉裝置，“啟用”指示將為真。有關維修工具密碼，請參閱附錄。模式啟用（僅狀態指示）調整用戶停止模式啟用指示（真/假）。當模式啟用時，參數為true——這表示可以更改“調整用戶停止”模式參數。如果為false，則只能查看參數，而不能調整參數。模式退出dflt=false（僅限瞬時真命令）退出命令。605-707109-012 Plc設置為true可退出“調整用戶停止”模式。這將禁用在此模式下更改參數的功能?！巴顺觥眳?shù)在退出完成后自動返回false。Auto Execute dflt=false（僅限瞬時真命令）執行自動“尋止器”程序的命令。當設置為true時，605-707109-012 Plc輸出移動到最小和最大位置，并自動確定停止。Status字符串指示當前執行步驟。設置停止時，該命令會自動設置回false。
選擇所需的校準模式。有兩種模式，手動沖程模式和自動模式。605-707109-012。如果選擇了自動模式，步驟7至11將自動執行，無需任何用戶輸入。通過將“自動執行”設置為true，605-707109-012可啟用自動模式。7.有兩種方法可以手動在最小和最大位置之間移動輸出：手動或使用手動設置位置。要使用手動設置位置，必須將手動啟用設置為true。使用手動設置位置定位ProAct，降低需求設置，直到致動器定位在最小停止位置，或者用手將輸出推入最小停止位置。8.將At Min Position（在最小位置）參數設置為true，以允許Control記錄最小位置設置。9.增加手動設定位置設置，直到致動器定位在最大停止位置，或者用手將輸出推入最大停止位置。10.將At Max Position（在最大位置）參數設置為true，以允許控制記錄最大位置設置。11.當Min和Max均已成功校準時，將Enable Manual Stroke（啟用手動沖程）設置回false（如果啟用手動校準）。如果成功，Calibration Status（校準狀態）將指示校準已完成。如果校準不成功，狀態將指示“失敗”。12.驗證校準。這可以手動完成，方法是將機架從最小值移動到最大值，觀察位置讀數（維修工具或模擬輸出），或?qū)⑹謩?dòng)啟用設置為真，并使用手動設置位置變量定位輸出。605-707109-01213.調整動態。調整執行器慣性設置以獲得正確的系統性能。增加設置意味著系統中的慣性更高，并導致致動器中的增益更高。使用執行器慣性測試執行命令驗證設置。關于基于操縱桿尺寸的近似慣性設置，請參閱表9-1。14.可選地，在每個停止處設置所需的偏移（偏置）。605-707109-012“硬件調整”中提供了“最小停止偏移”和“最大停止偏移”參數，基本上可以在用戶校準的停止設置內提供電氣停止。該偏移以行程的度數為單位，可以隨時調整。請參閱本章后面的圖9-5和維修模式：硬件調整。
This setting inverts the PWM input values to read the percentage of the time low rather than the percentage of the time high. Adjusting User Stops and Dynamics Introduction The User Calibration mode of the Service Tool provides the capability to set the min and max position to match the rigging of the actuator and valve. Both automatic and manual procedures are available to perform this setup. 605-707109-012This calibration must be done prior to operation of the unit.605-707109-012 If this procedure is not done, the actuator will be defaulted such that (0 to 100) % position demand will correspond to 0–75 degrees rotation. Refer to Figure 9-4. Once the user calibration is performed, this procedure stores the active min and max positions into non-volatile memory where it is retained until a new calibration is performed. In addition, 605-707109-012this mode can be used to verify the setup/calibration by providing a manual stroking mechanism.
AnlgIn 200 Min Value (mA) dflt= 20 mA(range 0.0–200) Analog Input Minimum Demand Value in mA. This setting corresponds to the milliamp signal that would demand the actuator to be fully closed (0 %) (should be less than the ’AnlgIn 200 Max Value (mA)’ setting).605-707109-012 AnlgIn 200 Max Value (mA) dflt=180 mA (range 0.0–200) Analog Input Maximum Demand Value in mA. This setting corresponds to the milliamp signal that would demand the actuator to be fully opened (100 %) (should be greater than the ’AnlgIn 200 Min Value (mA)’ setting). CAN DataRate default = 1(1, 3) CAN data rate setting in kbps. 605-707109-012Selection options: 1=250, 2=500, 3=1000 kbps. CAN Extensions default = 1 (0, 1) CAN Extension Configuration. This determines the messages of the CAN communications. The ProAct uses J1939 CAN but this setting sets up the actual Parameter Group Numbers (PGNs) and Suspect Parameter Numbers (SPNs) to be used over the comm link. Selection options: 0=Disable Can communications, 1=Set#1, 2=Set#2, etc. (must be greater than zero if CAN demand is configured). PwmIn Min Duty (%) default = 10 % (range 10–90) PWM Minimum actuator position Duty Cycle setting in percent. This setting corresponds to the duty cycle that would demand the actuator to be fully closed (0 %) (must be less than the ’PwmIn Max Duty (%)’ setting). PwmIn Max Duty (%) default 90 % (range 10–90) PWM Maximum actuator position Duty Cycle setting in percent. This setting corresponds to the duty cycle that would demand the actuator to be fully open (100 %) (must be greater than the ‘PwmIn Min Duty (%)’ setting).605-707109-012 PwmIn Frequency (Hz) dflt 1000 Hz (100–3000) Nominal PWM signal frequency in hertz. PwmIn Invert Input Signal dflt =false (false, true) Invert PWM Signal option. This configuration setting is available for systems that do not have a pull-up in their PWM output (refer to the hardware PWM section for details).
Demand—Primary Source dflt = 3 (1, 3) Select the source of the primary demand input. Selection options: 1=CAN, 2=PWM, 3=Analog. Demand—Backup Source dflt = 2 (0, 3) Select the source of the backup demand input. Selection options: 0= Not Used, 1=CAN, 2=PWM, 3=Analog605-707109-012 (Primary and Backup demand sources must be different). AnlgIn 20 Min Value (mA) dflt=4 mA (range 0.0–25) Analog Input Minimum Demand Value in mA. 605-707109-012This setting corresponds to the milliamp signal that would demand the actuator to be fully closed (0 %) (should be less than the ’605-707109-012AnlgIn 20 Max Value (mA)’ setting). AnlgIn 20 Max Value (mA) dflt=20 mA (range 0.0–25) Analog Input Maximum Demand Value in mA. This setting corresponds to the milliamp signal that would demand the actuator to be fully opened (100 %) (should be greater than the ’605-707109-012AnlgIn 20 Min Value (mA)’ setting).