LAM XVME-560 驅動板
產品概述：
XVME-560離散輸出配置設置。當為false時，只有關閉才會激活離散輸出。當為true時，任何報警或停機條件都將激活離散輸出。離散輸出包括Runenable[Run/Enable]dflt=true（false，true）（此參數僅適用于ProAct軟件2.10版或更高版本）（檢查服務：單元狀態下的版本號：）當設置為true時，當Run Enable離散輸入（低功率待機模式）觸點打開時，狀態輸出也將打開。當設置為false時，運行啟用（低功率待機模式）觸點的條件不會影響狀態輸出。Run Enable–Closed to Run dflt=true（false，true）（此參數僅適用于ProAct Software Version 2.20特殊固件XVME-560零件號5418-2590）（檢查“服務：單元狀態”下的版本號：）設置為true時，XVME-560運行啟用觸點將在運行模式下閉合，在低功率待機模式下打開。當設置為false時，運行啟用觸點將在運行模式下打開，在低功率待機模式下關閉。停機操作dflt=3（1,3）選擇檢測到停機條件時要執行的操作。選擇選項：1=最小，2=最大，3=Pwr向下。（請參閱停機說明待定）。溫度報警SP（°C）dflt=95°C（50150）高溫報警設定點，單位為攝氏度。此警報基于內部電子設備溫度。有關詳細信息，請參閱報警部分。溫度報警延遲（秒）dflt=1秒（0，10）高溫報警延遲（以秒為單位）。
XVME-560執行機構類型dflt=3（1=ProAct1，2=ProAct2，…4=ProAct4）ProAct執行機構類型配置。這被設置為適當?shù)腜roAct致動器（例如，ProAct Model 4將被設置為“4”）。執行機構CCW方向dflt=false（false=CW，true=CCW）ProAct執行機構方向配置——順時針與逆時針——從執行機構的軸端看。執行機構慣性設置dflt=0（范圍0–25）執行機構/閥門慣性設置。此設置適用于慣性高于或低于默認值的系統，如軸移動過大所示。XVME-560零（0）設置基本上適用于未連接的軸，而增加設置意味著系統中的慣性更高。該參數也可以在服務模式下進行調整和測試——有關詳細信息，請參閱調整用戶停止部分中的調整和測試致動器動態（有關更多詳細信息，見圖9-8）。高摩擦系統dflt=false（false，true）內部擾動觀測器控制器（dobs）啟用命令。通常設置為false，僅在高摩擦系統中需要。XVME-560該參數也可以在服務模式下進行調整，以確定是否需要它——有關詳細信息，請參閱調整用戶停止部分中的調整和測試致動器動態（有關更多詳細信息，見圖9-8）。
Like the Standard version, the Professional version of Watch Window software can be downloaded and This site can also be used to obtain license authorizations
Entering Configure Mode Select the Configure Mode tab sheet and shut down the driver by setting the Shutdown Command value to ‘true’ or by opening the Low Power Standby Mode discrete input.XVME-560 Enter the appropriate configure mode Password (1113) and either select ‘ENTER’ or click on the equals (=) box to the right of the password box. The ‘Enabled’ field will display ‘true’ if the Configure Mode has been successfully entered. Configure the unit by setting the Unit Setup and Demand Setup parameters to the application specific values. Refer to the Configure Mode Details section of the manual for details on these settings.XVME-560 As changes are made to Configure and Service mode parameters, they are automatically saved into non-volatile memory—no special ‘save’ command is required. XVME-560Configuring the Unit (Configure Mode parameters) Refer to the information provided later in this chapter for details on the Configure Mode parameters. A program summary worksheet is provided in the Appendix as an overview of all software settings in the ProAct control.
Watch Window Standard and Professional There are two versions of the Watch Window software, Standard and Professional. Watch Window Standard XVME-560is provided with the ProAct control as a Service Tool for Configuration, Tuning, and Monitoring. Watch Window Standard supports only Service and Configure modes. The Standard version of Watch Window will not display Factory Calibration, Test, and Debug mode values. Only the professional version has this capability. Watch Window Professional is available as a purchased upgrade, but is not required for this product. In addition to providing Factory Calibration,XVME-560 Test, and Debug mode access, the Professional version provides software download capabilities for new or revised software versions.XVME-560
The Inspector can have its configuration saved and restored. The Inspector can be closed by using the Main Window or by clicking the standard windows close button. Watch Window Decimal Places The number of digits displayed after the decimal place displayed in Watch Window can be adjusted from the Precision setting under the Watch Window Options menu. Watch Window Help More help on using Watch Window is available and included with the installation of the Watch XVME-560product. Watch XVME-560Help can be accessed from the Watch Window ‘Contents’ drop-down window selection under the Help menu located on the Main Window. Software Version Identification The Watch Window software version can found by selecting ‘About’ under the Help menu. The ProAct software version information can be found by selecting ‘Properties’ under the Control menu. Refer to this information in any correspondence with XVME-560